Duct Tape Crown and Tiara DIY

This wasn't completely a step by step tutorial. I was invited to a murder mystery party and my husband and I were assigned the roles or Mallory and Mike Majesty. I wanted a nice statement piece but I didn't want to pay much. So I went online and printed a crown template and did a simple crown for my husband. Using the same method and a self drafted template, I made one for myself.

Items needed:

• Poster board
• Regular duct tape
• Glittery/Iridescent duct tape
• Pattern
• Scissors
• Xacto knife

There isn't a picture for the first step, but I cut the poster board into the length and height of the crown I wanted to make. Then I covered the front (you can do both sides for a clean look) with black duct tape. Then I covered the duct tape with the iridescent duct tape.

This was the second step. I made two copies of the pattern, trimmed it down and taped it to the to the board. Then I used the scissors to cut around the pattern and used to xacto knife where needed for detailed rounds and corners. 

This was the final look of his crown. Once the details were cut, I taped the ends together for the final look. 

For my piece, I made the pattern in to a lattice shape. I was channeling the Toddlers and Tiara show crowns. For this one, I cut the cardboard down to the rough shape of the crown before putting the duct tape. I didn't want to waste a lot of my tape and reduce the trouble with cutting.  

 Using the Xacto knife, I cut out each diamond cutout and also cut around the outer curve of the crown.

This was the final look of my crown. 

Here are both pieces together along with the banners. 

Queen flat sheet and Standard Pillow Case into Fitted 6-ft Table Cloth Cover Upcycle

Oops, it's been a while since I did a blog. But on the positive note, I'm set to do my first craft show. I'm excited and scared at the same time. Since I signed up, I've been working on all the advice I got from various forums on what you need for a successful show. I designed new business cards, got a poster for display and then searched to find a fitted tablecloth. I saw this tablecloth on Amazon. It was $20, but I'd seen a neat trick for an art show covering and wanted something similar. But I didn't want to use the nice fabric I have in stash, nor did I want to spend $20 and then some more for the pockets.

New Business Card

I knew I wanted something to cover the entire table and allow me to put stuff away without others coming to the booth seeing it. I drafted up a rough design. I wanted to put in a zipper, but decided to keep this simple. 

 

What you need:

• 1 Queen flat sheets 90" X 102". (I went to Ross and got a queen sheet set for $15.99. I still have the fitted sheet and one pillow case)
• 1 standard pillow case 20" X 30"
• Measuring tape or ruler
• Something to mark with

 Sheet folded in half  along the short side(left) and Pillow case (right)

 First I opened the pillow case. So now it was about 30" X 40" take about an inch since I cut across the side seam and only ripped the short seam.

Fold a triangle out of the rectangle as seen below using the short side to come up at the longer edge.

 Cut the excess fabric below the triangle which will leave you with an almost perfect square that is 30" X 30".

Pin the square (right sides together) on the short end of the fold, making sure to center the two piece.

When you sew the pieces together, you will end up with one end having 30" squares on either sides of the new piece you added.

Fold the sheet the other way with the pillowcase in the middle forming two squares. Cut out the orange lines.

This is the result. You now have your side pieces. You will need to pin the sides of the leg together and sew with the right sides facing each other. I really hope this makes sense. You're sewing this like you would a fabric box as seen in this tutorial,except your box is much bigger.

When you're all done, it should slip on top of the table just like this.

For the pockets, I sewed them right to the tablecloth using the left over panels from the sheet that had been cut out for the sides. It was nice because I could use the finished side as the top of the pockets without having to hem then sew. Using a yard stick, I marked along the back side where I wanted my pockets. I did 3 that were 8 inches wide and 2 that were 10 inches wide.

I cut, prepped and pinned the pockets to the sheet then took it off to sew.

This is my finished look. Cost me less than $15 and I also have pockets and a spare fitted sheet to use on my bed or for another project. Maybe a dress shirt or another cover for my smaller 4-ft table. Since my log is pretty simple, I plan to take just the letters in my log and applique it to the other corner piece that I cut off and that I can hang to the front of my table.

Placemat Upcycle Purse Tutorial using two placemats and a belt

Needed: 2 lined placemats,

            1 zipper

            Fabric for pockets

            Magnetic snap

This tutorial is going to be pretty much following the pictures. My mother-in-law retired this month and for her retirement party I wanted to give her a personalized tote. Something she could put her books in during her leisure readings while retired.

I bought two placemats that were lined.

I separated the back and front of the placemats.

Here are the two pieces separated.

The wrong side of the front piece to the placemat was stiffened which made it a lot easier  to do the embroidery.

I used my Brother SE400 to embroider her first and last initials onto the right side of the placemat front.

On one of the wrong sides, I put in a side zipper pocket

On the second placemat's wrong side, I put in a side pocket.

This is the zipper side shown with the belt that became the handles for the tote.

Below the zipper pocket, I put in a smaller pocket and 3 pen holders.

I split the pocket to give her extra storage.

Sew the two lining pieces right sides together and square off the bottom. At this point, I also went ahead and installed the magnetic snaps for closing the main bag.

Sew on the handles to the right side of the placemat pieces.

Sew the outer part of the placemat right sides together like the lining and square off the bottom. Cut off the excess fabric.

Flip the outer bag right side out

Place the outer bag into the lining bag which is wrong side out. This way both of the right sides are facing each other.

 

Sew all around the lip of the bags leaving yourself about 4 to 6 inches for turning the tote right side out. Top stitch the bag lip all around closing your turning hole and you're done.

Here is the finished insides.

Here is her completed tote. 

Boy's Onesie Vest with Shorts and bow tie set. Size 18months

I had been playing around with adding boys outfits to my Etsy shop on account of my friends with boys asking why I have nothing for the boys. I have done some bodysuit/t-shirt dresses for the girls and wanted to make something special for my friend's son with the same African Inspiration as the other items in my shop. I have to give credit where it's due because Erica's tutorial that I found thru Pinterest helped with how make a pattern from the onsie. I posted my first pattern attempt to my facebook group and got many asking for patterns. I'd never done patterns for other before so I decided to give it a try. Using Erica's tutorial (link above), I drew out my pattern, cut the fabric out of an old bed sheet and did a fit test.

After tweaking until I was satisfied, I scanned the pattern and brought it into Autocad to get a clean drawing. 

This was my initial pattern. The picture is not to scale so if you tried to use this it wouldn't work. Don't worry, the pattern is coming. :-)

You will need: Size 18 month onsie/bodysuit, about 1/4 yard of lining and main fabric. Will need a little more if  you are using nap fabric.

So I made the new improved pattern and turned it into a PDF and starting on the final project which was a birthday gift to my friend's son.

I made mirror cuts of the pattern using the same fabric for the lining and main so sorry for confusion. Make sure to make all your markings. The pattern has an optional faux pocket for the vest.

 Using my serger, I sewed all around the pieces leaving the shoulders opened.

 Turn the pieces right side out and use a blunt tip object to push out the corners and then iron flat. At this point, you can chose to top stitch the vest before attaching to the body suit.

Place the vest on top of the body suit and mark the shoulder and underarm for where you want to tack. I marked about half inch on each shoulder.

 Hope the above image makes since. I flipped up the vest so that the half in lined up with the fold in the shoulders of the bodysuit. I pinned it to the shoulders with the lining facing up and sew across the shoulders. Make sure to open the neck and sew along the shoulder with the body suit not folder on itself. It's a little tricky, but try not to sew the front and back of the top together.

 Once it's sewn, flip the vest down , fold the corner of the remaining seam and top stitch the vest as you did before with the bodysuit opened.

Repeat on both sides.

Re-position the vest and mark(with a pin) where the bottom of the vest arm hole meets the bodysuit. 

Flip the vest to the side with the lining exposed. Reach into the bodysuit and pin the outer seam of the vest to the side seam of the bodysuit.

 Using the same method as when sewing on the shoulders, sew the vest side to the side seam keeping careful not to sew the bodysuit to itself. The inside of the bodysuit should look like the image on the right. there should be a straight seam running down the length of the side seam as long as the vest. I did a very narrow seam. Between 1/4 and 1/8 inch.

When you're done, the seam should look like this on the right side. As if it was sewn into the sides of the body suit.

I used my KAM kit to  add snaps to the vest using my markings from before. I learned that sewing the vest together restricts movement and you lose the stretch. With the ability to open the vest, you can also open it up if the kid is outgrowing the outfit.

Outfit with the bowtie.

 Outfit without the bowtie.

Great big thanks to my friend's son for modeling his birthday gift.

The pattern is free to use. Sorry right now it's only for a size 18months. Please Pin it, Share the blog and credit me if you use the pattern. You can tag me on Instagram or Twitter at @elsielorpu with an image of your creation.  You can also like my Facebook page and post your rendition of the vest or just link to my blog if you do and comment below. Thank you.